Call Now: 1-800-284-2288 |
X Series Amplifier |
|
|
The Crestron AMP-X300 is a high performance, space saving, energy efficient, professional grade amplifier solution that’s totally configurable, yet simple to use. Whether you need a stereo amp that mounts on a wall or under a table, or a multichannel rack mount amp with multiple output types and power levels, the AMP-X300 is simple to specify and install in any configuration.
LoZ (4/8 Ω) and Hi-Z (70 V or 100 V) Output
The AMP-X300 is a 4-channel amplifier (at 75 W per channel) which can also be configured for 2-channel bridged operation (at 150 W per channel), with a choice of “LoZ” outputs to drive 4- or 8‑-Ohm speakers, or “Hi-Z” outputs to drive a distributed speaker system (70 V or 100 V). Balanced and unbalanced inputs are provided for connection to two stereo or four mono source(s) via detachable terminal blocks or RCA connectors.
ICEpower® and Crestron Design
The AMP-X300 was designed in partnership with ICEpower® to create a custom, flexible, high performance amplifier topology that is suitable for a variety of audio applications.
Solid & Efficient Performance
The AMP-X300 is engineered to deliver exceptional performance and reliability with low distortion, low noise, and high power headroom. Advanced Class D technology maximizes efficiency to reduce power consumption and heat dissipation. An internal universal power supply ensures consistent performance at varying line voltages.
Convection Cooling
The efficient design ensures cool running operation to ensure long term reliability. The AMP-X300 is high-density stackable with other Crestron modular amps, allowing multiple units to be installed vertically in an equipment rack without needing extra ventilation space.
Modular Design
The AMP-X300 is housed in a half-width rack-mountable form factor that can be installed individually or ganged together in a single rack space. The amplifier ships complete with all the hardware required for installation. Rack and surface mount parts are included, so there are no other mounting accessories or rack shelves to purchase.
Whether mounting in a rack, attaching to a flat surface, or placing on a shelf, it’s easy to combine two amplifiers into a single assembly.
Fully Protected
The AMP-X300 features protection against overheating, shorted or overloaded speaker lines, excessive input signals, and other faults. In the case of a shorted speaker line or overheating condition, both outputs mute automatically until the fault condition is resolved. In the event of a prolonged fault, such as an internal component failure, the outputs mute instantly and the amplifier shuts down.
ENERGY STAR® Certified
An energy-efficient design enables the AMP-X300 to meet demanding ENERGY STAR requirements. In addition to its high efficiency under operation, the AMP-X300 draws no added inrush current during power-up, thereby reducing AC circuit requirements and allowing multiple units to be connected to a single switched circuit. To reduce energy usage further, the AMP-X300 can be configured to enter a low-power standby state if no input signal is detected on either channel for 25 minutes. Signal detection has been optimized for sensitivity to improve response time when triggering the amplifier to the "on" state, allowing it to return to full operation within a half-second the instant an input signal is detected.
Audio | |||||||||||||||||||||||||||||||||||||||||||
Input Signal Types | Balanced or unbalanced analog line-level | ||||||||||||||||||||||||||||||||||||||||||
Output Power
|
|||||||||||||||||||||||||||||||||||||||||||
NOTE: Total output power from all channels combined (simultaneously) is 300 W | |||||||||||||||||||||||||||||||||||||||||||
Frequency Response | 20 Hz to 20 kHz ±0.5 dB at 1 W | ||||||||||||||||||||||||||||||||||||||||||
High-Pass Filter(70 V and 100 V operation only) | -3 dB @ 80 Hz, -12 dB/octave | ||||||||||||||||||||||||||||||||||||||||||
THD+N | <0.1% at 1 kHz @ -3 dB full rated output power | ||||||||||||||||||||||||||||||||||||||||||
S/N Ratio | >103 dBA, 20 Hz to 20 kHz, balanced |
||||||||||||||||||||||||||||||||||||||||||
Crosstalk | -75 dB at 1 kHz | ||||||||||||||||||||||||||||||||||||||||||
Input Sensitivity | 1.23 Vrms, +4 dBu balanced; 0.316 Vrms, -10 dBV unbalanced; For 150 W (8 Ohms), 300 W (8 Ohms Bridged), 300 W(70 V/100 V) |
||||||||||||||||||||||||||||||||||||||||||
Gain | 29 dB @ 8 Ohms | ||||||||||||||||||||||||||||||||||||||||||
Protection | Over current, under voltage, over temperature, DC offset, extreme high frequency | ||||||||||||||||||||||||||||||||||||||||||
Go to Sleep Time | 25 minutes with no signal present (when set to POWER SAVER) | ||||||||||||||||||||||||||||||||||||||||||
Wake Time | 0.5 s typical | ||||||||||||||||||||||||||||||||||||||||||
Wake Threshold | 0.44 mV typical | ||||||||||||||||||||||||||||||||||||||||||
Connectors | |||||||||||||||||||||||||||||||||||||||||||
CH1-CH4 | (2) 4‑pin 5.08 mm pitch, 12 A plug with screw locking retainers; Power amplifier output; Wire Size: Terminals accept up to 12 AWG (3.31 mm2) NOTE: Output is direct‑coupled, not transformer isolated |
||||||||||||||||||||||||||||||||||||||||||
AUDIO IN (UNBALANCED) | (4) RCA connectors, female; Unbalanced line‑level audio inputs (Summing on CH1 + CH2 and CH3 + CH4); Maximum Input Level: 2.24 Vrms, +7 dBV (+9.2 dBu) |
||||||||||||||||||||||||||||||||||||||||||
AUDIO IN (BALANCED) | (4) 3-pin 3.5 mm detachable terminal block; Balanced line‑level audio inputs; Channel pairs 1 - 2 and 3 - 4 can each be configured to operate as stereo channels or a downmixed mono channel; Maximum Input Level: 7.75 Vrms, +20 dBu; Input Impedance: 20k Ohms |
||||||||||||||||||||||||||||||||||||||||||
G | (1) 6-32 screw; Chassis ground lug |
||||||||||||||||||||||||||||||||||||||||||
100‑240V~ 1.2-0.6 A 50/60 Hz | (1) IEC 60320 C14 main power inlet; Mates with removable power cord, included |
||||||||||||||||||||||||||||||||||||||||||
Controls & Indicators | |||||||||||||||||||||||||||||||||||||||||||
PWR | (1) White/Red LED; White indicates amplifier is on and ready for use; Red indicates amplifier is in standby |
||||||||||||||||||||||||||||||||||||||||||
HI-Z | (1) White LED; Indicates when Hi-Z mode is enabled (70 V or 100 V); Channels 1 - 2 and 3 - 4 are bridged and set to 70 V or 100 V operation |
||||||||||||||||||||||||||||||||||||||||||
SIGNAL | (4) White LEDs (one per input); Indicates when an active input signal is present |
||||||||||||||||||||||||||||||||||||||||||
FAULT | (4) Red LEDs (one per input); Indicates that the input channel is faulted or clipping |
||||||||||||||||||||||||||||||||||||||||||
GAIN 1-4 | (4) Screwdriver‑adjustable rotary controls, one per input channel; Adjusts the input attenuation level for the corresponding input channel |
||||||||||||||||||||||||||||||||||||||||||
LoZ Modes | (2) Slide switches, 1 switch for CH1 + CH2, 1 switch for CH3 + CH4; Selects stereo, summed, or bridged operation
|
||||||||||||||||||||||||||||||||||||||||||
Operations Mode | (1) Slide switch; Sets the amplifier LoZ (4 or 8 Ω) or Hi-Z operation (70 V or 100 V) |
||||||||||||||||||||||||||||||||||||||||||
Power Mode | (1) Slide switch; Selects "Power Saver" or "Always On" operation |
||||||||||||||||||||||||||||||||||||||||||
Power | |||||||||||||||||||||||||||||||||||||||||||
Main Power | 1.2-0.6 A @ 100‑240 VAC, 50/60 Hz | ||||||||||||||||||||||||||||||||||||||||||
Power Consumption | 75 W, (4 channels driven at 1/8th output power, 4 ohms); 16 W, idle (Hi-Z mode); 0.365 W, power saver (230VAC/50Hz) |
||||||||||||||||||||||||||||||||||||||||||
Environmental | |||||||||||||||||||||||||||||||||||||||||||
Temperature | 41 to 104° F (5° to 40° C) | ||||||||||||||||||||||||||||||||||||||||||
Humidity | 10% to 90% RH (non-condensing) | ||||||||||||||||||||||||||||||||||||||||||
Construction | |||||||||||||||||||||||||||||||||||||||||||
Chassis | Metal, convection cooled (fanless) | ||||||||||||||||||||||||||||||||||||||||||
Front Panel | Metal, black finish with polycarbonate label overlay | ||||||||||||||||||||||||||||||||||||||||||
Mounting | Freestanding, surface mount, or 1/2 width 1 RU 19 in. rack mountable; gangable with other Crestron modular AMP series products (adhesive feet and surface mounting kit included; ganging kit and rack mounting kit optional) | ||||||||||||||||||||||||||||||||||||||||||
Dimensions | |||||||||||||||||||||||||||||||||||||||||||
Height | 1.75 in. (44 mm) without feet; 1.83 in. (46 mm) with feet |
||||||||||||||||||||||||||||||||||||||||||
Width | 8.67 in. (220 mm) without mounting brackets 19.00 in. (483 mm) with mounting brackets |
||||||||||||||||||||||||||||||||||||||||||
Depth | 11.04 in. (280 mm) | ||||||||||||||||||||||||||||||||||||||||||
Weight | |||||||||||||||||||||||||||||||||||||||||||
5.3 lb (2.4 kg) | |||||||||||||||||||||||||||||||||||||||||||
Compliance | |||||||||||||||||||||||||||||||||||||||||||
ENERGY STAR, ErP (1275/2008/EC), UL 62368, FCC Class B residential use |
ss_amp-x300.pdf | datasheet |
ss_amp-x300.pdf | datasheet |
Call Now: 1-800-284-2288 |
|||||
Email Us: sales@avsupply |
|||||
|