Call Now: 1-800-284-2288 |
(discontinued) 3-Series Control System |
|
|
This item is DISCONTINUED.
The Crestron CP3 presents a new benchmark in control system technology. Featuring the 3-Series™ control engine, the CP3 forms the core of any modern networked home or commercial building, managing and integrating all the disparate technologies throughout your facility to make life easier, greener, more productive, and more enjoyable.
Available Configurations Include:
CP3-GV | 3-Series Control System® - Government Version |
CP3N | 3-Series Control System® |
CP3 features include:
Control Engine | ||
3-Series™; real-time, preemptive multi-threaded/multitasking kernel; Transaction-Safe Extended FAT file system; supports up to 10 simultaneously running programs | ||
Memory | ||
SDRAM | 512 MB | |
Flash | 4 GB | |
Memory Card | supports SD™ and SDHC™ cards up to 32 GB | |
External Storage | support USB mass storage devices up to 1 TB | |
Communications | ||
Ethernet | 10/100 Mbps; auto-switching; auto-negotiating; auto-discovery; full/half duplex; industry-standard TCP/IP stack; UDP/IP; CIP; DHCP; SSL; IEEE 802.1X; SNMP; BACnet®/IP[1]; IPv4 or IPv6; Active Directory authentication; IIS v.6.0 Web Server; SMTP e-mail client; installer setup via Crestron Toolbox™ or MSIE[2] | |
Cresnet® | Cresnet master mode | |
USB | Supports USB HID and USB mass storage class devices via rear panel USB 2.0 host ports, supports computer console via front panel USB 2.0 device port | |
RS-232/422/485 | For 2-way device control and monitoring, all ports support RS-232 up to 115.2k baud with software handshaking, one port also supports RS-422 or RS-485 and hardware handshaking | |
IR/Serial | Supports 1-way device control via infrared up to 1.2 MHz or serial TTL/RS-232 (0-5 Volts) up to 115.2k baud | |
Connectors & Card Slots | ||
RELAY OUTPUT 1 – 8 | (2) 8-pin 3.5mm detachable terminal block comprising (8) normally open, isolated relays; Rated 1 Amp, 30 Volts AC/DC; MOV arc suppression across contacts |
|
I/O 1 – 8 | (1) 9-pin 3.5mm detachable terminal block comprising (8) “Versiport” digital input/output or analog input ports (referenced to GND); Digital Input: Rated for 0-24 Volts DC, input impedance 20k Ohms, logic threshold >3.125V low/0 and <1.875V high/1; Digital Output: 250mA sink from maximum 24 Volts DC, catch diodes for use with “real world” loads; Analog Input: Rated for 0-10 Volts DC, protected to 24 Volts DC maximum, input impedance 21k ohms with pull-up resistor disabled; Programmable 5 Volts, 2k ohms pull-up resistor per pin |
|
IR - SERIAL OUTPUT 1 – 8 | (2) 8-pin 3.5mm detachable terminal block comprising (8) IR/Serial output ports; IR output up to 1.2 MHz; 1-way serial TTL/RS-232 (0-5 Volts) up to 115.2k baud |
|
COM 1 | (1) 5-pin 3.5mm detachable terminal block; Bidirectional RS-232/422/485 port; Up to 115.2k baud; hardware and software handshaking support |
|
COM 2 – 3 | (2) 3-pin 3.5mm detachable terminal blocks; Bidirectional RS-232 ports; Up to 115.2k baud; software handshaking support |
|
MEMORY | (1) SD memory card slot; Accepts one SD or SDHC card up to 32 GB for memory expansion |
|
USB | (1) USB Type A female; USB 2.0 port for storage devices |
|
LAN | (1) 8-wire RJ45 jack; 10Base-T/100Base-TX Ethernet port |
|
NET | (1) 4-pin 3.5mm detachable terminal block, Cresnet master port; Outputs power to Cresnet devices if a power pack is connected to the 24VDC power input jack; Receives Cresnet network power if no power pack is connected to the 24VDC power input jack; See “Power Requirements” for additional specifications |
|
24VDC 2.0A | (1) 2.1 x 5.5 mm DC power connector, 24 Volt DC power input; PW-2420RU power pack included; Passes through to NET port to power Cresnet devices; See “Power Requirements” for additional specifications |
|
G | (1) 6-32 screw, chassis ground lug | |
COMPUTER (front) | (1) USB Type B female; USB 2.0 computer console port (6 ft cable included); For setup only |
|
Controls & Indicators | ||
PWR | (1) Green LED, indicates operating power supplied from power pack or Cresnet network | |
NET | (1) Amber LED, indicates communication with the Cresnet system | |
MSG | (1) Red LED, indicates control system has generated an error message | |
HW-R | (1) Recessed pushbutton for hardware reset | |
SW-R | (1) Recessed pushbutton for software reset | |
LAN (rear) | (2) LEDs, green LED indicates Ethernet link status, amber LED indicates Ethernet activity | |
Power Requirements | ||
Power Pack | 2.0 Amps @ 24 Volts DC; 100-240 Volts AC, 50/60 Hz power pack, model PW-2420RU included |
|
Available Cresnet Power | 24 Watts (1 Amp @ 24 Volts DC) when using power pack | |
Cresnet Power Usage | 15 Watts (0.625 Amp @ 24 Volts DC) when using Cresnet network power | |
Environmental | ||
Temperature | 41° to 113°F (5° to 45°C) | |
Humidity | 10% to 90% RH (non-condensing) | |
Heat Dissipation | 50 BTU/Hr | |
Enclosure | ||
Chassis | Metal, black finish | |
Faceplate | Extruded metal, black finish, polycarbonate label overlay | |
Mounting | Freestanding or 1U 19-inch rack-mountable (adhesive feet and rack ears included) | |
Dimensions | ||
Height | 1.70 in (44 mm) without feet | |
Width | 17.28 in (439 mm), 19.00 in (483 mm) with rack ears | |
Depth | 6.56 in (167 mm) | |
Weight | ||
3.12 lb (1.42 kg) |
cp3.pdf | Datasheet |
Call Now: 1-800-284-2288 |
|||||
Email Us: sales@avsupply |
|||||
|