1/2" Interline Progressive CCD SXGA 19 fps 1360 x 1040 Monochrome Camera
|
|
By: Sentech
Industrial, USB, & Medical Cameras
|
The STCPOGE152A is part of Sentech's Power Over Ethernet GigE camera line. It features a 1/2" monochrome SXGA sensor, 19fps and communication over a 12 pin Hirose or Ethernet connector.
The STC POGE152A boasts precision housing with accurate CCD alignment, a DC Auto Iris Lens Driver, a user-programmable Area of Interest (AOI) and a Gamma Table that can be imported. This camera meets all industry standards for GigE Vision� and GenICam�.
→ 1/2" CCD Image Sensor
→ SXGA (1.3 Megapixel), 19fps
→ PoE (Power Over Ethernet)
Imager | 1/2" Interline SXGA monochrome progressive CCD: ICX205AL
|
Total Picture Element | 1434 (H) x 1050 (V)
|
Active Picture Element | SXGA: 1360 (H) x 1040 (V)
|
Chip Size | 7.6 (H) x 6.2 (V) mm
|
Cell Size | 4.65 (H) x 4.65 (V) µm
|
Scanning System | Progressive
|
Vertical Frequency (Frame Rate) | 19.25954 Hz at full resolution 0.31387 to 71.66965 Hz adjustable via the communication Max. frame rate depends on the AOI setting Max. frame rate of the camera(71.66965) is 200 vertical resolution AOI setting
|
Horizontal Frequency | 20.5688 kHz
|
Pixel Frequency | 36.818175 MHz
|
Noise Level - @ 8bit output | ≤ 3 Digit (Gain 0 dB)
|
Noise Level - @ 10bit output | ≤ 12 Digit (Gain 0 dB)
|
Noise Level - @ 12bit output | ≤ 48 Digit (Gain 0 dB)
|
Minimum Scene Illumination | 0.41 Lux at F1.2, 19.25954 Hz
|
Sync System | Internal
|
Video Output | Digital 8, 10 or 12 bit Raw Data
|
Interface | PoE: IEEE802.3af (1000BASE-T)
|
Protocol | GigE Vision® 1.2 and GenICam™ 2.0 compliant
|
Shutter Speed | Preset continuous mode: 10 useconds to 17,666,216 useconds Preset trigger mode: 10 useconds to 17,666,216 useconds Pulse width mode: 10 useconds to Unlimited
|
ALC | Auto iris lens, electronic iris and AGC (ON / OFF)
|
Gain | 0 to 20.4 dB
|
Gamma | Gamma 1.0 (Factory default) or downloadable gamma table
|
AOI Function | Programmable AOI setting via the communication
|
Smear Reduction | Selectable ON / OFF via the communication
|
Trigger Mode | Edge preset trigger, Pulse width trigger (unlimited long exposure)
|
Communication | UART communication through Ethernet port
|
I/Os | 3 opto-isolated inputs and 5 opto-isolated outputs
|
Auto IRIS lens control | DC IRIS control input with video level target, peak/average and zone weight settings via the communication
|
Power - Input Voltage | 10.8 to 26.4 Vdc through power/IO connector or Power Over Ethernet (Auto detection with power/IO connector prioritized)
|
Power - Consumption | < 4.5 W
|
Dimensions | 50 (W) x 50 (H) x 53.5 (D) mm excluding connectors
|
Optical Filter | No filter
|
Optical Center Accuracy | Positional accuracy in H and V directions: /0.3 mm Rotational accuracy of H and V: /1.5 deg.
|
Material | Aluminum (AC)
|
Lens Mount | C mount
|
Connectors | RJ45 connector Power/IO connector: HR10A-10R-12PB (Hirose) or equivalent DC IRIS lens connector: M1951 (EMUDEN) or equivalent
|
Camera Mount Screws | Two 1/4” Tripod screw holes: (One on each top and bottom plate), Sixteen M4 screws holes: (Four on each top, bottom and both side plates)
|
Weight | Approximately 170g
|
Operating Temperature | -5 ~ 40 deg. C
|
Storage Temperature | -30 ~ 65 deg. C
|
Vibration | 20 Hz to 200 Hz to 20 Hz (5 min. /cycle), acceleration 10G, 3 directions 30 min. each
|
Shock | Acceleration 38G, half amplitude 6 ms, 3 directions 3 times each
|
Standard Compliancy | TBD
|
RoHS | RoHS Compliant
|
© 1996 - 2024 | All Rights Reserved
Audio Video Supply Inc.
4542 Ruffner St. Suite 220
San Diego, CA 92111
Prices and specifications subject to change without notice.